Skip to main content

Every building is a running argument with gravity, and gravity never gets tired. A roof wants to fall, a floor wants to sag, wind wants to push a tower over, and the ground shakes now and then. Structure is the part of architecture that answers these forces. You do not need equations to understand it, only a feel for pushing and pulling.

Loads and the path they take

Engineers sort the forces on a building into loads. The dead load is the weight of the building itself: its walls, floors, roof and fixed equipment. The live load is everything that comes and goes, such as people, furniture, books and snow. Then there are environmental loads from wind and earthquakes, which push sideways rather than down. The load path is the route by which forces travel from where they act down into the ground: from a floor to its beams, from beams to columns or walls, from columns to foundations, and from foundations into soil or rock. Reading a building's structure means tracing that path. If you cannot see where the weight goes, someone has either hidden the structure or made a mistake.

Pushing and pulling

Materials feel forces in two basic ways. Compression is a squeezing force; tension is a pulling force. A column carrying a roof is in compression. A cable holding up a bridge deck is in tension. A beam does both at once: when it sags, its top edge is squeezed and its bottom edge is stretched. This is why material matters so much. Stone and brick are strong in compression but weak in tension. You can stack them very high, but a long stone beam will crack along its underside. Timber and steel handle tension far better.

Post and lintel

The simplest way to make an opening is to set a beam across two uprights. Post and lintel construction uses a horizontal beam laid across two vertical supports. It is found everywhere, from wooden houses to Egyptian temples. In stone it has a built-in limit. Because a stone lintel fails in tension, it cannot span far, and so stone temples have columns standing close together like a forest. The closely spaced columns that give such temples their rhythm are partly a record of what the material could not do.

The arch and its family

The arch solves the stone problem in a clever way. An arch turns the weight above it into compression along its curve, so every wedge-shaped stone is squeezed against its neighbors and none is pulled. The central stone at the top is the keystone, and while an arch is being built its stones rest on a temporary wooden frame called centering. Once the keystone is set, the arch holds itself. But an arch also pushes outward at its base. This sideways push is called thrust, and it must be resisted by heavy walls, buttresses or neighboring arches. Much of the history of large buildings is the history of handling thrust.

The arch has relatives. A vault is an arch extended into a tunnel or crossed with another to make a ceiling. A dome is, roughly, an arch rotated around its center. Domes have a special weakness near their base, where the masonry tends to spread outward, and builders have long tied them with iron chains or heavy rings to stop them cracking open.

Triangles, frames and cantilevers

For spanning long distances with light parts, builders turned to the triangle. A truss is a framework of members joined in triangles, which hold their shape under load. A square of sticks with loose joints folds flat, but a triangle cannot change shape without one side changing length. Roof trusses, railway bridges and stadium roofs all rely on this.

Modern towers usually use a frame. In a frame structure, a skeleton of columns and beams carries the floors, so walls need not bear weight. That freedom lets walls become thin skins of glass. A frame can also reach out into space. A cantilever is a beam supported at only one end, like a diving board or a balcony that seems to float, and it works by balancing the load against a firm anchor at the other end.

Worked example: the Pont du Gard

In southern France stands a Roman bridge built in the first century AD to carry an aqueduct across the river Gardon on its way to the city of Nîmes. It rises in three tiers of arches to almost 50 meters. Trace the load path. The water channel at the top presses down on the small upper arches. They pass their load to the larger arches below, and those deliver it through thick piers into the riverbed rock. Every stone is in compression, which is exactly what stone does best. Many of the big blocks in the lower tiers were laid without mortar, held in place by their own weight and careful cutting.

Notice how thrust is handled. Each arch pushes sideways, but in a row of equal arches the push of one is balanced by the push of the next, so only the ends need heavy support. The engineering also served a public end. The whole aqueduct fell only about 12 meters over a route of roughly 50 kilometers, delivering a steady flow of fresh water for fountains, baths and homes. The bridge is admired as beautiful, but its beauty is inseparable from its logic: the shapes are the forces made visible.

Quiz

5 questions · Practice: scored, not saved

1. What is a building's dead load?
2. What is the load path?
3. What is the difference between compression and tension?
4. Why do stone temples have closely spaced columns?
5. How does an arch carry weight?
6. What is thrust in an arch?
7. Why does a truss hold its shape?
8. What is a cantilever?

CivilSimian.com created by AxiomaticPanic, CivilSimian, Kalokagathia